FastMigMXP 37 Pipe SteelMXP 37 Pipe StainlessMXP 38Operating manualBrugsanvisningGebrauchsanweisungManual de instruccionesKäyttöohjeManuel d’utilisati
EN2.7 Loading the ller wire and automatic feedAutomatic wire feed makes wire spool changes faster. When changing the wire spool, the pressure of fee
ENWire feed rolls, plasticø mm lower upperFe, Ss, (Al, Mc, Fc)V-groove0.6 W001045 W0010460.8 – 0.9 W001047 W0010481.0 W000675 W0006761.2 W000960 W0009
EN2.9 DuraTorque™ 400, 4-wheel wire feed mechanism in MXP 38Wire guide tubesø mm outlet tube middle tube inlet tubeSs, Al, (Fe, Mc, Fc)plastic0.6 W0
ENAl, (Fc, Mc, Ss, Fe)U-groove1.0 W001067 W0010681.2 W001069 W0010701.6 W001071 W001072Wire feed rolls, metalø mm lower upperFe, Ss, (Al, Mc, Fc)V-gro
EN2.10 Adjustment of pressure armsAdjust the drive pressure to the ller wire with the thumb screws mounted over the pressure arms. Notice the gradua
EN2.14 Shielding gasNOTE! Handle shielding gas bottle with care. Assess the risks associated with handling and using compressed gas. Always use a cy
EN2.15 Main switch I/OWhen you turn the main switch of the FastMig power source into I-position, the pilot lamp closest to this switch will illuminat
EN3.2 LayoutXF 37W007241CH REMOTECHANNELPANEL4T2T 1. 3.2.4.5. 6.7. 8. 9.10.11.1. ON/OFF button2. Activates MIG welding dynamics (short press) Selec
EN3.3 Button functions3.3.1 ON/OFF button (1)XF 37W007241CH REMOTECHANNELPANEL4T2T Short press: XF 37 / X 38 panel returns to initial display.Long p
EN3.3.7 2T/4T button (7)XF 37W007241CH REMOTECHANNELPANEL4T2T Short press: Toggles between 2T or 4T gun trigger mode.Long press: Turns MatchLog ON/OF
EN3.4 Welding softwareThe FastMig MXP wire feeders are compatible with the following modied welding processes and functions• WiseRoot+™ is a modie
ENPIPE STEEL PACKGroup Material Wire ø (mm) Shielding gas Process NumberFe Fe 0.8 Ar+15–25%CO₂ WiseRoot+ F01Fe Fe 0.9 Ar+15–25%CO₂ WiseRoot+ F02Fe Fe
ENWORK PACKGroup Material Wire ø (mm) Shielding gas Process NumberAl AlMg5 1.2 Ar Pulse/Double Pulse A02Al AlSi5 1.2 Ar Pulse/Double Pulse A12Fe Fe 1.
EN4. BASIC TROUBLESHOOTINGNOTE! The problems listed and the possible causes are not denitive, but serve to suggest some standard and typical situat
ENErr 4Power source is overheated• Do not shut down, let the fans cool the machine. • Check ventilation. • If cooling fans are not running, contact
EN5. MAINTENANCEWhen considering and planning routine maintenance, please consider the frequency of machine use and the working environment. Correct
EN6. DISPOSAL OF THE MACHINEDo not dispose of electrical equipment with normal waste!In observance of European Directive 2002/96/EC on waste electric
ENWisePulseMig™ licence for pulse welding Included with MXP 37 Pipe Stainless and MXP 38 wire feeders9990417WiseRoot+™ Included with MXP 37 wire feede
ENMIG gunsPMT MN 1.2 mm / 60° / L198 / ROOT 3.5 m 62503230N04PMT MN 1.2 mm / 60° / L168 / ROOT 3.5 m 62503230N06PMT MN 1.2 mm / 60° / L198 / ROOT 5 m
EN8. TECHNICAL DATAFastMig MXP 37 Pipe FastMig MXP 38Operating voltage (safety voltage) 50 V DC 50 V DCRated power250 W 100 WOutput 40 °C60 % ED 52
OPERATING MANUALEnglish
www.kemppi.com19037001515KEMPPI OYKempinkatu 1PL 13FIN-15801 LAHTIFINLANDTel +358 3 899 11Telefax +358 3 899 [email protected]
ENCONTENTS1. Introduction ... 31.1 General ...
EN1. INTRODUCTION1.1 GeneralCongratulations on choosing the FastMig MXP welding equipment. Used correctly, Kemppi products can signicantly increase
EN2. INSTALLATION2.1 Machine introduction: MXP 37 Pipe and MXP 38MXP 37 Pipe MXP 384.2.1.3.5. 2.1.3.5.4.6.1. Control panel XF 37 1. Cont
EN2.2 Connecting cables2.2.1 Liquid-cooled system: FastMig X 450 + MXP + FastCool 101.4.8.10.2.3.9.5.6.11.7.VV1. Wire feed unit2. FastMig X 450 po
EN2.2.2 Air-cooled system: FastMig X 450 + MXP 1.4.5.10.6.8.2.3.7.9.VV1. Wire feed unit2. FastMig X 450 power source3. Gas supply4. MMA electrode
EN5. Mounting FastMig wire feed units to boom and swing armsWhen mounting wire feed units to boom and swing arms, the unit must be electrically isolat
Comments to this Manuals